1000t/d Active Lime Production Line
Introduction
Jiangsu Pengfei Group manufactures the complete set of equipment for the 1000t/d active lime production line or active lime equipment. Our company undertakes the design and manufacture of rotary kiln, shaft cooler, vertical preheater and electrical control system according to clients’ requirements. It meanwhile supplies refractory materials. Pengfei introduces advanced technology from abroad to manufacture the vertical preheater, shaft cooler and limestone rotary kiln.
Technical Features of Active Lime Equipment
Main features of 1000t/d active lime production line are listed below:
1.The vertical preheater has an advanced structure. The preheater has effectively improved preheating effect. Limestone decomposition rate reaches 20% to 25%. Limestone of 10 to 15 mm grade could directly be used in this preheater.
2.A round or square shaft cooler in the rotary kiln makes the temperature of lime goes up to 800℃ plus ambient temperature. It makes the limestone suitable for transportation and storage. This cooler can also preheat the secondary air to over 7000℃. It reduces movable parts and special materials of the active lime production line or active lime equipment.
3.The two ends of the rotary kiln are sealed by fish scale type seal method. The air leakage rate is less than 10%. Radiant heat loss is therefore reduced.
Process Flow
1.Preheating
Limestone is heated to 900℃ by the 1150℃ kiln gas in the preheater of 1000t/d active lime production line.
2.Calcining
Hydraulic push rod of this active lime equipment sends the limestone into the rotary kiln. The limestone is calcined and decomposed into CaO and CO2.
3.Cooling
Decomposed limestone is then sent into cooler of the active lime production line. The lime is cooled to less than 100℃ by cold air and then is discharged out.
4.Waste Gas Treatment
The 600℃ hot air enters into kiln and burns with coal gas. The waste gas is then mixed with cold air. Draft fan of this active lime equipment sends the waste gas into bag dust collector. Exhaust fan then discharges the waste gas into chimney.
Introduction
Jiangsu Pengfei Group manufactures the complete set of equipment for the 1000t/d active lime production line or active lime equipment. Our company undertakes the design and manufacture of rotary kiln, shaft cooler, vertical preheater and electrical control system according to clients’ requirements. It meanwhile supplies refractory materials. Pengfei introduces advanced technology from abroad to manufacture the vertical preheater, shaft cooler and limestone rotary kiln.
Technical Features of Active Lime Equipment
Main features of 1000t/d active lime production line are listed below:
1.The vertical preheater has an advanced structure. The preheater has effectively improved preheating effect. Limestone decomposition rate reaches 20% to 25%. Limestone of 10 to 15 mm grade could directly be used in this preheater.
2.A round or square shaft cooler in the rotary kiln makes the temperature of lime goes up to 800℃ plus ambient temperature. It makes the limestone suitable for transportation and storage. This cooler can also preheat the secondary air to over 7000℃. It reduces movable parts and special materials of the active lime production line or active lime equipment.
3.The two ends of the rotary kiln are sealed by fish scale type seal method. The air leakage rate is less than 10%. Radiant heat loss is therefore reduced.
Process Flow
1.Preheating
Limestone is heated to 900℃ by the 1150℃ kiln gas in the preheater of 1000t/d active lime production line.
2.Calcining
Hydraulic push rod of this active lime equipment sends the limestone into the rotary kiln. The limestone is calcined and decomposed into CaO and CO2.
3.Cooling
Decomposed limestone is then sent into cooler of the active lime production line. The lime is cooled to less than 100℃ by cold air and then is discharged out.
4.Waste Gas Treatment
The 600℃ hot air enters into kiln and burns with coal gas. The waste gas is then mixed with cold air. Draft fan of this active lime equipment sends the waste gas into bag dust collector. Exhaust fan then discharges the waste gas into chimney.
